Spray foam insulation in Greater Vancouver

Attic Spray Foam Insulation

Attics lose heat fast. Spray foam can help when the roof or ceiling assembly is designed for it. We check before we spray.

Call 604-373-9598 Free quote

Free quote
Fast site check
Clean install
Call 604-373-9598

Free quoteNo drama.

Clean prepMask. Spray. Trim.

Code-awareAsk first.

Local crewGreater Vancouver.

Project photos

Real foam. Real spaces.

Installer preparing attic framing for spray foam insulation in Vancouver — Attic framing checked before insulation work.

Roofline insulation installed between rafters under open sky — Roofline insulation between attic rafters.

Insulation contractor checking attic roof insulation with a hard hat — Contractor checking attic insulation details.

Contractors measuring attic insulation depth near a skylight in Vancouver — Insulation depth and roofline details measured.

Best fit

Use it where air leaks steal money.

attic spray foam insulation Vancouver works best when the goal is simple: stop drafts, slow heat loss, and control moisture paths before they become expensive repairs.

We look at the framing, sheathing, vents, mechanicals, wiring, and access. Then we tell you what foam makes sense, what does not, and what needs a different insulation plan.

No upsell fog. Just the right scope.

Attic hatches
Kneewalls
Roofline foam
Penetration sealing
Garage attic transitions
Hard-to-reach cavities

What you get

A tight envelope without the circus.

The job starts with masking and protection. Then surfaces are checked, cleaned, and sprayed in controlled passes. We watch temperature, expansion, and coverage. The site is left tidy.

Good foam should look boring after it cures. Continuous. Even. No voids. No random bulges where trim, drywall, trades, or inspections need clean access.

That is the work. Measure. Prep. Spray. Trim. Clean. Done.

Ventilation review
Moisture check
Penetration sealing
Neat transitions
Clear prep list
Thermal-barrier discussion

Avoid this

Bad foam is expensive foam.

Spray foam can fail when it is sprayed over damp surfaces, mixed wrong, buried without required protection, or used in an assembly that needs ventilation or different vapour control.

We flag those risks early. Sometimes the right recommendation is closed-cell foam. Sometimes it is batt plus air sealing. Sometimes it is an engineer or code consultant before anyone sprays.

Better a clear no than a messy yes.

Covering roof leaks
Blocking required vents
Wrong hot-roof approach
Unsealed pot lights
No fire protection plan
Insulating over wet materials

Code-ready work

Foam is only good when the prep is good.

Spray foam is not paint. It is a building envelope decision. We check moisture, access, ventilation, ignition-barrier needs, and assembly type before the rig starts.

For medium-density closed-cell polyurethane foam, BC code references CAN/ULC-S705.1 for the material standard. Installation details matter. Product, applicator, substrate, lift thickness, and curing conditions all need respect.

Simple rule. Right foam. Right place. Right thickness. Clean site. No mystery.

Moisture check before install
Open-cell vs closed-cell explained
Fire and thermal barrier conversation
Clean cut lines and sealed penetrations

Vancouver climate

Wet coast. Cold drafts. Tight cavities.

Greater Vancouver homes see rain, damp crawl spaces, older framing, and heat loss through rim joists, attics, garages, and basement walls. Spray foam helps because it insulates and air seals at the same time.

Closed-cell foam can add a strong air and vapour-control layer where the assembly calls for it. Open-cell foam can fit some interior sound and air-sealing uses. The best answer depends on the wall, roof, crawl space, and permit path.

We do not guess. We look first. Then we quote.

Crawl spaces
Rim joists
Garage ceilings
Attics and rooflines
Basement walls
Commercial metal buildings

Questions

Fast answers.

How much does attic spray foam insulation Vancouver cost?

It depends on access, square footage, thickness, foam type, masking, removal, and whether ignition or thermal protection is needed. Call 604-373-9598 and we will price the real job.

Do you use open-cell or closed-cell foam?

Both can make sense. Closed-cell is common for air sealing, moisture control, and high R-value per inch. Open-cell can fit some interior and sound-control uses. The assembly decides.

Can spray foam help with drafts?

Yes. Spray foam expands into cracks and gaps, so it can reduce air leakage where batts alone leave paths for cold air.

Do I need to leave during install?

Usually yes during spraying and curing. We will explain timing before the job so people, pets, and trades stay clear.

Do you serve all of Greater Vancouver?

Yes. We focus on Vancouver, West Vancouver, North Vancouver, Burnaby, and nearby Lower Mainland areas.