Spray foam insulation in Greater Vancouver

Mobile Spray Foam Estimates

We come to the space, check the access, check the assembly, and quote the job. Simple.

Call 604-373-9598 Free quote

Free quote
Fast site check
Clean install
Call 604-373-9598

Free quoteNo drama.

Clean prepMask. Spray. Trim.

Code-awareAsk first.

Local crewGreater Vancouver.

Project photos

Real foam. Real spaces.

Installer spraying closed-cell spray foam insulation into wall framing in Vancouver — Closed-cell foam sprayed into wall framing.

Spray foam insulation installed between wall studs and roof framing — Fresh spray foam in a framed room.

Closed-cell spray foam being applied inside a framed wall cavity — Closed-cell foam filling a wall cavity.

Spray foam installer in protective suit applying insulation to a wall — Protected installer applying foam cleanly.

Best fit

Use it where air leaks steal money.

mobile spray foam estimates Vancouver works best when the goal is simple: stop drafts, slow heat loss, and control moisture paths before they become expensive repairs.

We look at the framing, sheathing, vents, mechanicals, wiring, and access. Then we tell you what foam makes sense, what does not, and what needs a different insulation plan.

No upsell fog. Just the right scope.

Homeowner quotes
Contractor site checks
Strata walkthroughs
Commercial takeoffs
Renovation planning
Pre-drywall checks

What you get

A tight envelope without the circus.

The job starts with masking and protection. Then surfaces are checked, cleaned, and sprayed in controlled passes. We watch temperature, expansion, and coverage. The site is left tidy.

Good foam should look boring after it cures. Continuous. Even. No voids. No random bulges where trim, drywall, trades, or inspections need clean access.

That is the work. Measure. Prep. Spray. Trim. Clean. Done.

Photos reviewed first
Site visit when needed
Access and masking checked
Foam type explained
Written scope
Scheduling window

Avoid this

Bad foam is expensive foam.

Spray foam can fail when it is sprayed over damp surfaces, mixed wrong, buried without required protection, or used in an assembly that needs ventilation or different vapour control.

We flag those risks early. Sometimes the right recommendation is closed-cell foam. Sometimes it is batt plus air sealing. Sometimes it is an engineer or code consultant before anyone sprays.

Better a clear no than a messy yes.

Quoting from bad photos
Ignoring access
Wrong square footage
No fire barrier allowance
No prep allowance
Surprises after arrival

Code-ready work

Foam is only good when the prep is good.

Spray foam is not paint. It is a building envelope decision. We check moisture, access, ventilation, ignition-barrier needs, and assembly type before the rig starts.

For medium-density closed-cell polyurethane foam, BC code references CAN/ULC-S705.1 for the material standard. Installation details matter. Product, applicator, substrate, lift thickness, and curing conditions all need respect.

Simple rule. Right foam. Right place. Right thickness. Clean site. No mystery.

Moisture check before install
Open-cell vs closed-cell explained
Fire and thermal barrier conversation
Clean cut lines and sealed penetrations

Vancouver climate

Wet coast. Cold drafts. Tight cavities.

Greater Vancouver homes see rain, damp crawl spaces, older framing, and heat loss through rim joists, attics, garages, and basement walls. Spray foam helps because it insulates and air seals at the same time.

Closed-cell foam can add a strong air and vapour-control layer where the assembly calls for it. Open-cell foam can fit some interior sound and air-sealing uses. The best answer depends on the wall, roof, crawl space, and permit path.

We do not guess. We look first. Then we quote.

Crawl spaces
Rim joists
Garage ceilings
Attics and rooflines
Basement walls
Commercial metal buildings

Questions

Fast answers.

How much does mobile spray foam estimates Vancouver cost?

It depends on access, square footage, thickness, foam type, masking, removal, and whether ignition or thermal protection is needed. Call 604-373-9598 and we will price the real job.

Do you use open-cell or closed-cell foam?

Both can make sense. Closed-cell is common for air sealing, moisture control, and high R-value per inch. Open-cell can fit some interior and sound-control uses. The assembly decides.

Can spray foam help with drafts?

Yes. Spray foam expands into cracks and gaps, so it can reduce air leakage where batts alone leave paths for cold air.

Do I need to leave during install?

Usually yes during spraying and curing. We will explain timing before the job so people, pets, and trades stay clear.

Do you serve all of Greater Vancouver?

Yes. We focus on Vancouver, West Vancouver, North Vancouver, Burnaby, and nearby Lower Mainland areas.